Kitchen lighting planner

What is your kitchen like?

Floor plan from above

Base cabinet Wall cabinet Splashback Plinth On top of cabinets

{{ wl.name }} {{ wl.note }}

SSupply cable from the driver LLink cable from the previous run

Cabinet lights {{ selTitle }}

No light in this cabinet.

Cables: {{ zs.label }} The light is interrupted wherever there is no light (for example a cooker hood, a dishwasher or a cabinet with its light removed). Each continuous stretch is its own run. Markers in the image: S = supply cable from the driver, L = link cable from the previous run. Choose whether each run gets its own supply or the runs are chained with link cables.

Which end the supply comes from, run by run:

{{ is.label }} {{ is.txt }}

Supply m

Supply cable (all) m

Corner cable cm

Link cable m

Selected cabinet {{ selTitle }}

Type Width

Click a cabinet to change its type, width or position, or to remove it. Add cabinets with the + button at the end of the row.

Wall cabinets at the corner

{{ co.label }}

Drag into a row or reorder cabinets by dragging

Light positions

Light colour for the whole kitchen The same tone for all lights so the surfaces look consistent. The colour limits the strips offered below.

Where should light go? Select all light positions. Each selected position gets its own step where you choose a profile and a strip for it.

{{ z.label }} {{ z.desc }} {{ z.stats }}

{{ zs.kicker }} {{ zs.label }} {{ zs.desc }} {{ zs.stats }}

1. Choose a profile

The first one is our recommendation for this position. Click an image to enlarge it.

No dimension drawing

Recommended

{{ pc.name }}

{{ ln.k }}: {{ ln.v }}

2. Choose an LED strip

No suitable strip fits the selected profile for this position. Choose another profile.

{{ sc.name }} {{ sc.price }}

{{ ln.k }}: {{ ln.v }}

Not recommended here ({{ zs.badN }})

{{ sc.name }} {{ sc.price }}

{{ ln.k }}: {{ ln.v }}

Splashback light output Estimated illuminance on the worktop Calculated from the strip's measured luminous flux, the profile position and surface reflectance. Side section at the middle of the cabinet.

Splashback {{ sec.gapLabel }} · {{ sec.depthLabel }} Lux across the worktop depth · dashed line = {{ graph.tLabel }} · scale 0–{{ graph.maxLabel }}

Average{{ lux.avg }}

Weakest point{{ lux.min }}

Uniformity{{ lux.u }}

Worktop tone{{ lux.lum }}

Profile position {{ lux.posLabel }}

Splashback height: {{ gapH }} cm

Wall cabinet depth Worktop depth

Worktop

Splashback panel

I'll collect from the store. Profiles in full length. Otherwise they are cut into pieces of max 150 cm for shipping, with cut points following the cabinets.

1. Group the lights

Lights in the same group switch on and dim together. By default, task lights are in group 1 and ambient lights in group 2.

{{ cz.label }} · {{ cz.w }}

2. Choose a control method for each group

Click a group and choose its control method. The driver is sized to the group's power.

{{ selGroupTitle }}

3. {{ remoteTitle }}

Driver and accessories

{{ xg.title }}

Zigbee receiver (between driver and strip)

Switch soldered to the strip (1 per light position)

Lights and strips

{{ z.label }} {{ z.stats }}

{{ ln.k }}: {{ ln.v }}

Strip · {{ z.rule }}

{{ ln.k }}: {{ ln.v }}

Measurement list and profile lengths

You can shorten an individual profile if the light should not run the full length of the cabinet. The strip is recalculated.

{{ c.title }}
{{ c.sub }} Profile cm {{ c.max }}

Why these choices

Read the kitchen lighting guide →

Your package

{{ pkgCount }} products

Total {{ total }}

Request a quote

Request a lighting design

{{ zoom.cap }} {{ zoom.title }}

Open product page →

{{ heading }}

What is your kitchen like?

{{ wallsTitle }}

1. Choose a profile

2. Choose an LED strip

1. Group the lights

2. Choose a control method for each group

3. {{ remoteTitle }}

{{ remoteProdTitle }}

Driver and accessories

Lights and strips

Your package

Does the button fit your switch range?